
Cosmetic Packaging FAQ: MOQ, Samples, Lead Time and Certifications
Thirty-one answers to the questions buyers ask us before a first order: how we count MOQ, what a sample costs, how long production takes, which certificates travel with the goods, and what happens when something goes wrong.
We wrote each answer to stand on its own, so you can forward a single line to a colleague or a client without sending the rest of the page.
Ordering and MOQ
Q: What is the minimum order quantity for cosmetic packaging?
A: We start at 1,000 pcs for a standard build with no change to colour, logo, or size. A custom build - your logo, a matched colour, or a new size on an existing mould - starts at 3,000 pcs. We apply the same two-tier rule to jars, bottles, tubes, and boxes, and we print the exact figure for each product on its product page.
Q: Can I combine different models or colours to reach the MOQ?
A: Yes. We count MOQ per model, and you can combine several models in one order to reach it. A 3,000 pcs order can carry three colours, as long as each colour clears the per-colour minimum for that decoration method. When an order mixes materials - glass jars with bamboo lids and printed boxes - we assemble and inspect it as one lot.
Q: Do you accept trial orders below the MOQ?
A: On a stock model we will discuss a smaller first order, and we quote it as a trial order rather than as a discount. We usually advise against custom decoration below 3,000 pcs, because the plate or die charge spreads over fewer units; for a first run we would rather you take a stock colour and keep the unit cost down.
Q: Is there a minimum for reorders?
A: A reorder on an approved specification usually runs below the first-order MOQ, because the plate and the mould are already paid for. The figure depends on the decoration method, and we confirm it on your reorder quotation rather than leave you to assume it.
Samples and Prototyping
Q: Are samples free?
A: A stock sample is free and you pay the courier; it usually arrives in 3-7 days by DHL, UPS, TNT, or FedEx. A decorated sample with your logo carries a sample charge and takes 7-10 days, and we credit that charge against your first bulk order, so it works as a deposit rather than as a cost.
Q: How long does a new mould take?
A: We run 25-30 days from approved drawing to first shot, then 7-10 days for the sample. We send drawings back within 24 hours with the points that will not mould as drawn - wall thickness, draft angle, undercuts - because correcting a drawing costs nothing and correcting a tool does not.
Q: Can you send the sample to my forwarder in China?
A: Yes. Give us the forwarder's address and a contact name, and we ship the sample there with the same tracking. We do this routinely for buyers who consolidate cargo in Shenzhen or Ningbo, and it saves you a second international courier charge.
Lead Time and Shipping
Q: What is the production lead time?
A: We run bulk production 15-25 days after sample approval, depending on the process: injection-moulded jars and bottles sit at the lower end, airless packs and heavily decorated lines at the upper end. Airless bottles can take 25-35 days. We plan against the date on your quotation, which is a date we commit to, not an average.
Q: What are the shipping terms?
A: We quote FOB Shanghai. Bulk orders ship by sea from Shanghai port, and small lots or urgent replenishments go by express with DHL, UPS, TNT, or FedEx. We prepare export packing, palletising on request, and the full document pack before the vessel sails.
Q: Can you handle a rush order?
A: We schedule urgent orders into the same QC process, not around it, so a shorter lead time changes the calendar rather than the number of inspection gates. Tell us the date you need the goods in your warehouse, not the date you need them to leave China, and we quote against the real constraint.
Q: Who arranges the freight and the documents?
A: Either of us can. We can book through our forwarder and hand you the full document pack, or work with your forwarder and send the documents straight to you. We prepare customs clearance documents before shipment so paperwork is never the reason a container waits at the port.
Customization and Artwork
Q: What can be customized?
A: Six levers: colour, logo and branding, capacity, shape, closure, and liner. Colour covers natural, tinted, sprayed, electroplated, and Pantone-matched. Branding covers laser engraving, silkscreen, hot stamping, UV printing, and labels. A shape beyond our existing moulds means a new tool, which we cut in 25-30 days.
Q: What artwork format do you need?
A: We work from AI, PDF, or EPS with text converted to outlines, 300 dpi for any raster element, and Pantone references for spot colours. We issue a dieline per pack and per size, and your artwork has to sit on that dieline rather than on a rectangle, because the print area changes with the bottle.
Q: Can I print my logo on bamboo?
A: Yes, by laser engraving, which burns the mark into the grain with no plate charge and cannot rub off. We start that at 3,000 pcs. Silkscreen also works on the sealed surface. What we advise against is a full opaque coating or a full-colour print on bamboo - it covers the grain, which is the reason you specified bamboo in the first place.
Q: How is colour matched?
A: We match colour on a physical chip, sprayed on your actual substrate, before production. The same Pantone reads differently on clear glass and on white PP, so a screen proof does not settle it. For gradients we fix the direction and the start point on the drawing, because a gradient decided at the machine cannot be repeated on the second lot.
Quality and Testing
Q: What inspection standard do you work to?
A: We work to AQL critical 0, major 2.5, minor 4.0 on every lot, checked at four gates: incoming material, in-process, final inspection, and pre-shipment. We hold a lot that fails a gate rather than rework it quietly, and we make the inspection record for your lot available to you.
Q: How do you test for leaks?
A: We put every production lot through an in-line leak check, and we hold filled samples inverted for 24 hours at 40 C, with no seepage permitted, before packing. The seal is a function of the gasket and the closure torque, both set to the viscosity you quote, so we do not test a thin serum and a thick cream the same way.
Q: Can a third party inspect my order?
A: Yes. We welcome SGS, Intertek, or your own inspector at any gate with two weeks notice, so the lot is still on the floor and not already packed. The report you commission is yours; we do not ask to review it before it reaches you.
Q: What happens if the goods arrive damaged or out of specification?
A: Send us photographs and the inspection record reference. We acknowledge the complaint first, then answer with a root cause and a written corrective action, and we agree the remedy - replacement, credit, or rework - against the specification both sides approved, not against opinion.
Compliance and Documents
Q: Which certificates do you hold?
A: We hold ISO 9001 for the quality system across our four production bases, we source FSC-certified bamboo on request, and we issue material declarations for product-contact parts: FDA food-contact and EU 10/2011 for inner liners, REACH and RoHS for all materials. We share heavy-metal and migration test reports with your compliance team before the first order.
Q: Can you support EU and US market entry?
A: Yes, within the scope of the materials we supply. For the EU, we work to EU 10/2011 for plastic food-contact parts and EU 1935/2004 for food-contact materials generally; for the US, we issue FDA food-contact declarations for the liner and product-contact components. Tell us the destination country at quotation stage and we quote the right documents with the goods.
Q: Do you issue a declaration of conformity?
A: We issue material declarations and compliance statements for the parts we make, listing the regulation and the material covered. Where your market requires a specific format or a notified-body test, tell us the standard and we commission it and quote it as a separate line rather than assume it.
Q: Can I see the test reports before ordering?
A: Yes. We mask our details on the copy we send and keep yours confidential. Our reports cover heavy metals and migration for product-contact materials. If your formula needs a test we have not run, we say so rather than send you a report for a different material.
Payment, After-Sales and Factory Visits
Q: What payment terms do you accept?
A: We accept T/T and Western Union. We state the deposit and balance schedule on the quotation for your order, and we issue a copy of the proforma invoice before production starts. We quote payment terms for a first order and for a repeat order separately, because they are not always the same.
Q: Can I visit the factory?
A: Yes, at our Hangzhou and Tongxiang bases. Tell us which processes you want to see - moulding, glass finishing, printing, assembly, or inspection - and we build the route around production rather than around a meeting room. We arrange visits in advance so the line you want to see is actually running.
Q: Who owns the mould if I pay for it?
A: We write the ownership terms into the quotation before the tool is cut, so there is no ambiguity later. Tell us at quotation stage whether you need the mould to remain yours, because it changes the tooling line item and, in some cases, the unit price.
Q: How fast do you respond to a complaint?
A: We acknowledge a complaint first, then answer with a root cause and a written corrective action. Photographs, the lot number, and the inspection record reference shorten this considerably; a description alone usually leads us to a second round of questions.
Materials and Sustainability
Q: Is the bamboo sustainably sourced?
A: We source bamboo from FSC-certified forests, with chain-of-custody documents available on request. It is a fast-renewing grass rather than a timber, and we kiln-dry every part to 8-12% moisture and seal it on six faces before assembly, which is what keeps a cap stable in a humid bathroom.
Q: Does the formula touch the bamboo?
A: No. Our bamboo constructions use an inner liner - frosted glass or food-grade PP - and the liner is the product-contact surface. That is why we treat pH compatibility as a liner question, not a shell question: glass is indifferent across roughly pH 1 to 13, food-grade PP handles about pH 2 to 12.
Q: Can you supply recycled or PCR material?
A: We can supply PCR content on request, and the achievable percentage depends on the polymer and the part. Rather than publish a headline figure, we confirm what is available for your specific pack at sampling and state it on the quotation, because a percentage we cannot repeat lot to lot is not a specification.
Q: Are the packs recyclable?
A: We supply PP, PET, and HDPE parts that are recyclable in the streams that accept them, and glass is recyclable without qualification. Mono-material construction - a PP bottle with a PP piston, shoulder, and actuator - enters the PP stream without disassembly, which is why we specify it for refill programmes. Mixed-material assemblies are recyclable only where the stream separates them.
If your question is not here, send it to us
A specific question about your formula, your filling line,
or your market gets a specific answer, usually the same working day.




