Free Samples: Cosmetic Packaging in Your Hand in 3-7 Days
A stock sample is free. You pay the courier, and it reaches most destinations in 3-7 days. If you need your logo on it, a decorated sample takes 7-10 days and carries a sample charge that is credited against your first bulk order. No account, no minimum, no purchase order needed to start - send the capacity and the closure type and we ship.
Three Kinds of Sample, Three Different Answers
|
Type |
What you receive |
Cost |
Time |
Answers the question |
|
Stock sample |
An existing pack, no logo, in the closest available colour and closure |
Free, freight collected |
3-7 days |
Is this shape, capacity, and closure right for my product? |
|
Decorated sample |
Your logo on a real part, in your colour, with the closure you chose |
Sample charge, credited against your first bulk order |
7-10 days |
Will the decoration survive the curve, the seam, and the coating? |
|
Tooled sample |
A first shot from a new mould built to your drawing |
Tooling quoted separately |
25-30 days tooling, then 7-10 days |
Does the shape I designed actually mould and fill? |
Most buyers need the first two. The third is for a shape that does not exist yet, and it starts with a drawing, not a sample.
Four Steps, No Account Needed
|
Step |
What happens |
Who does it |
|
1. Send the request |
Capacity, closure type, decoration if any, destination country, and how many units you expect to order |
You |
|
2. Confirm the pick |
We reply with the exact SKU, the colour available, and the courier cost |
Us, within one working day |
|
3. Ship |
Courier account or freight collected; tracking number sent the day it leaves |
Us |
|
4. Review |
You check fit, output, seal, and finish against the specification |
You, with our spec sheet in hand |
If the stock sample is close but not exact, say so in step 1. We would rather send the nearest pack with a note on what differs than send the wrong one and lose a week.
What to Send With Your Request
|
Item |
Example |
Why it matters |
|
Capacity |
30 ml, 50 ml, 100 g |
Decides which mould applies |
|
Format |
Bottle, jar, tube, airless, dropper |
Decides the sample family |
|
Closure |
Lotion pump, fine-mist sprayer, dropper, screw cap |
Decides the neck finish and the leak test |
|
Material or liner |
Frosted glass, food-grade PP, PET |
Decides the chemistry window and the declarations |
|
Decoration |
Laser engraving, silkscreen, hot stamping |
Decides whether a plain sample is enough |
|
Artwork |
AI, PDF, or EPS |
Needed only for a decorated sample |
|
Destination country |
Germany, United States, Japan |
Decides which test reports travel with the sample |
|
Expected quantity |
3,000 pcs, 20,000 pcs |
Decides whether the MOQ and the decoration minimum are met |
No artwork is needed for a stock sample. That is the point of a stock sample.
What a Sample Proves Before You Order
|
Check |
How to test it on the sample you receive |
What it tells you |
|
Neck and closure fit |
Screw the closure on and off ten times |
Whether the thread is cut to the right pitch, and whether it seizes |
|
Seal |
Fill with water, invert for 24 hours at 40 C, look for seepage |
Whether the gasket and the closure torque hold for your viscosity |
|
Pump output |
Dispense ten strokes and weigh or measure |
Whether the engine meters what your label claims |
|
Compatibility |
Leave your formula in the pack for a week at room temperature |
Whether the liner is right - glass, PP, and PET behave differently |
|
Colour |
Compare against your Pantone chip in daylight, not under a desk lamp |
Whether the coating thickness is even at the shoulder |
|
Bamboo grain |
Compare two caps side by side |
Why no two bamboo parts are identical, and why the lot is agreed as a direction |
A sample cannot prove everything. It cannot prove lot-to-lot consistency, and it cannot prove how the pack behaves on your filling line at 200 units a minute. Those are covered by the inspection record and by a trial run, and both are worth asking about before a large first order.
Timing and Freight
|
Item |
Detail |
|
Stock sample dispatch |
Same or next working day after confirmation |
|
Stock sample transit |
3-7 days by DHL, UPS, TNT, or FedEx |
|
Decorated sample production |
7-10 days, then transit |
|
Tooled sample |
25-30 days tooling, then 7-10 days sample production, then transit |
|
Freight basis |
Collected on your courier account, or quoted and prepaid |
|
Bulk shipment |
By sea from Shanghai, or by express for small lots |
|
Documents with the sample |
Spec sheet and, on request, material declarations for the destination market |
What Is Free and What Is Not
|
Item |
Free |
Charged |
|
Stock sample unit |
Yes |
- |
|
Courier freight |
- |
Yes, collected or prepaid |
|
Decorated sample |
- |
Yes, credited against your first bulk order |
|
Artwork dieline |
Yes |
- |
|
Colour chip on your substrate |
Yes, for an active project |
- |
|
New mould |
- |
Yes, quoted before it is cut |
|
Test report for a specific standard |
- |
Quoted as a separate line when the test has to be commissioned |
Sample charges are credited, not refunded. The amount comes off the first bulk invoice, which keeps the paperwork to one transaction instead of two.
Sample Questions We Get Every Week
Q: Can you send the sample to my forwarder in China instead of to my office?
A: Yes. Give us the forwarder's address and a contact name, and the sample ships there with the same tracking. This is common for buyers who already consolidate cargo in Shenzhen or Ningbo.
Q: How many stock samples can I ask for at once?
A: Ask for the packs you are actually comparing, usually two to four. Each one costs us a courier booking and a packing hour, and a box of twenty unrelated packs rarely helps a decision.
Q: Will the decorated sample be exactly what the bulk lot looks like?
A: It is made on the same line with the same method, so it is the reference the lot is measured against. Natural materials such as bamboo still vary in grain from batch to batch, and that is stated on the sample note.
Q: What if the sample is wrong for my formula?
A: Tell us what happened - seepage, softening, colour change, a pump that will not prime. We change the liner or the engine and send a second sample. That is cheaper for both of us than a bulk lot that fails.




