Every gift set has one component nobody photographs and everybody depends on: the transparent tray that stops the bottle from moving. It is the cheapest part in the box and the one most likely to hold up a launch, because the material decision now carries regulatory weight that it did not five years ago.
This guide covers what blister trays are made from, how they are formed, which defects are worth rejecting, and why PVC is quietly leaving the category.

What blister packaging actually is
Blister packaging is a thermoforming process. A flat plastic sheet is heated until it softens, drawn against a mould by vacuum or air pressure, cooled, and trimmed. Sheet below roughly 2 mm is usually called film or sheet; above that it is a board and behaves differently.
For cosmetics the output is almost always an inner tray or a display shell: a shaped cavity that locates one or more units inside a folding carton or a rigid box.
Four properties explain why the format is everywhere. It is light, so freight cost stays low. It is clear, so the product sells itself on shelf. It is cheap at volume. And because the cavity is shaped to the product, a carton needs no additional cushioning.
A formed tray is also rarely a standalone part. It is one of the cosmetic packaging parts that has to fit a carton, a label and a closure, which is why the tray and the box are usually specified together.
Materials, and what each one costs you
|
Material |
Clarity |
Heat resistance |
Recyclability |
When to use |
|
PVC |
High |
Moderate |
Poor, chlorine-based, rejected by most sorters |
Legacy tools only; avoid for new programmes |
|
APET |
Very high, haze under 3% |
Up to about 60 °C |
Widely recycled as PET stream |
Default for clear cosmetic trays |
|
RPET |
High, slight colour shift |
Similar to APET |
Recycled content claim |
Where PCR content is required |
|
PETG |
High |
Moderate |
PET stream, lower sorting yield |
Thick-wall or deep-draw trays |
|
PP |
Moderate, translucent |
Up to about 100 °C |
Widely recycled, mono-material |
Hot-fill adjacent, or mono-material sets |
|
PS |
Very high |
Low, brittle |
Limited |
Low-cost display shells |
|
PLA or PLA/PBAT |
High |
55 °C standard, 80 °C modified |
Industrial compost only |
Compostable claims with certification |
Two material notes are worth carrying into every RFQ. First, density drives cost per tray more than price per kilo: PP at roughly 0.9 g/cm³ yields more trays per tonne than PVC at 1.4 g/cm³, which often closes the apparent price gap. Second, clarity is measurable. Ask for a haze value, not a photograph.
The PVC question
PVC still performs well. It forms easily, takes a clean trim, and holds detail in deep cavities. The problem is what happens after use.
PVC contains chlorine, which makes it difficult to sort and undesirable in most mechanical recycling streams. A tray that contaminates a PET bale is worse than a tray that goes to energy recovery, because it degrades the value of everything around it. That is why collectors and sorters reject it, and why brands with public packaging commitments have been moving away from it for years.
The regulatory direction reinforces this. The EU Packaging and Packaging Waste Regulation entered into force in 2025 and applies from 12 August 2026, with recyclability requirements tightening over the following years. A tray that cannot be sorted into an existing stream becomes a design problem, not a compliance problem you can paper over.
There is also a residual monomer question. Vinyl chloride monomer is a known concern in PVC production, and buyers should ask for a supplier declaration on residual content rather than assume a default.
The practical answer for new programmes is APET, RPET or PP. Our eco-friendly cosmetic packaging range covers the mono-material formats that fit this shift.
How a tray is formed
The process is short, and almost all quality variation comes from three variables: sheet temperature, draw depth and cooling.
Sheet is unwound and clamped into a frame.
Heaters bring the sheet to its softening range. Too cold and the corners thin out; too hot and the sheet sags before forming.
The mould rises and vacuum pulls the sheet against it, sometimes assisted by plug assist for deep cavities.
Cooling. This step sets the final dimensions, so a short cooling cycle shows up later as warpage in the carton.
Demoulding and trimming, either in-line or on a separate die.
Two design numbers control whether the tool will run at rate. Keep the draw ratio, the depth of the cavity against its width, under about 1.5 to 1 for a simple cavity without plug assist. And keep every vertical wall drafted by at least two degrees, otherwise the tray grips the mould and distorts on release.
Separately, sealing is its own process with its own parameters. Where a blister is heat-sealed to a printed card, the seal cycle has a press time and a heat time that have to be tuned together: too short and the bond is cold, too long and the lacquer blisters. Voltage or current setting on a high-frequency sealer behaves the same way, and the correct starting point depends entirely on the coating, so it must be set on the actual card stock.
Defects worth rejecting
Webbing. A fold or ridge where the sheet was drawn too far or too fast, usually in a corner. In industrial trays it can be tolerated if it is cosmetic; in a cosmetic gift box it reads as a defect.
Scratches. Clear sheet shows every handling mark. Inspect under a raking light rather than overhead light, which is the fastest way to see what a customer will see.
Gels and specks. Contamination or unmelted polymer, visible as bright points in clear sheet. These come from the sheet extrusion, not the forming, which is why sheet supplier control matters as much as the forming line.
Bubbles and flow marks. Trapped air or thermal history in the sheet. Flow marks appear most in PVC and least in PET; the thicker the sheet, the more visible they become.
Warpage. A tray that rocks on a flat surface will not sit square in the carton. Measure it, don't eyeball it.
Set an AQL for each of these and write it into the quality agreement. Trays are usually inspected at general inspection level II with an AQL of 2.5 for cosmetic defects and 0.65 for functional ones.
Design rules that quietly save money
Nest the cavities to use the sheet. Sheet utilisation is the largest single cost driver in the tray, and a 10% improvement in nesting is a 10% material saving with no tooling change.
Keep wall thickness even. Deep draws thin the walls at the base, and a thin base is where cracks start. If you need a deep cavity, use plug assist rather than pushing the draw ratio.
Add ribs instead of thickness. A single rib doubles stiffness for a fraction of the material that extra gauge would cost.
Match the tray to the carton. The tray should locate the product and the carton should locate the tray. If both try to do both, tolerances stack and the set rattles.
For set construction, our beauty product packaging pages show how a folding carton, a rigid box and a moulded or formed insert are combined, and the beauty product sample boxes range is a useful reference for small-format trays.
What is actually changing in 2026
Three shifts are visible in live programmes.
PVC to APET or RPET. This is now the default migration and it is usually cost-neutral once density and recyclability are priced in.
Mono-material sets. A PP tray with a PP label and a PP carton can be recycled as one unit. Brands with published packaging targets are asking for it, even at a small cost premium.
Certified compostables, used narrowly. PLA and PLA/PBAT blends with third-party certification make sense for single-dose sampling, where the tray is small, contaminated with product and never going to be recovered. For a gift set, compostable material is usually a worse environmental answer than a recyclable one.
A tray rarely ships on its own. The case it sits inside has its own tolerances for hinge life, mirror retention and pan fit, and those are set out in our guide to eyeshadow palette packaging.
Frequently asked questions
Is APET suitable for a cosmetic tray that ships in summer?
Yes, for most cosmetic products. APET holds its shape to around 60 °C, which is above any realistic container interior during transport. If the tray sits against a vehicle panel in direct sun, use PP instead and accept the lower clarity.
Can one tool run both APET and PP?
Not well. The two materials shrink differently, so a mould cut for APET produces a warped or undersized tray in PP. Budget for a separate tool, or design the cavity for PP from the start if mono-material is likely.
How thick should a blister tray be?
Most cosmetic trays run between 0.4 mm and 0.8 mm. Go thinner only when the cavity is shallow and the product is light. Thickness at the base after forming is what matters, not the starting gauge.
What does a compostable tray claim require?
A third-party certificate against a recognised standard, such as TÜV OK compost INDUSTRIAL, plus a defined disposal route. A material data sheet saying "biodegradable" is not a claim that will survive a retailer's packaging review.
Sourcing cosmetic trays
Send the product dimensions, the carton internal size and the required PCR percentage, and ask for a tray proposal with a sheet utilisation figure and a haze value. Our custom beauty product sample boxes page is a practical starting point for small-format sets, and trays can be quoted as part of the same assembly so the fits are checked together.




